Exactly How to Install a Bath Tub in Your Bathroom
Exactly How to Install a Bath Tub in Your Bathroom
Blog Article
We have noticed this great article relating to Tools You Need to Install a New Bathtub down the page on the internet and thought it made sense to discuss it with you here.
Setting up a bath tub isn't exactly brain surgery, yet it does require solid plumbing, woodworking, and also in some cases, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably difficult job. If the old bathtub is conveniently available, the job can relocate speedily; if you have to open up a wall surface to get rid of the old tub as well as place the brand-new bathtub, the task is much harder. In either situation, the task is within a home handyman's skills, although you will require an assistant to vacate the old bathtub and set in the new one. Make sure you have qualified on your own for the work and also are comfortable attempting it. Rather than employing a specialist to take control of a halfway-completed task, it is better to consider employing one prior to you begin. Chances are you might require a specialist plumber to make tube links.
This post will help you mount a brand-new tub in your restroom if you have actually already bought a brand-new bathtub as well as don't require to transform the plan of your previous supply of water pipelines.
Your devices as well as material list should consist of the following:
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installment, after that the first thing you must do is detach the supply of water. After doing so, switch on the taps to drain any water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather problematic as a result of the limited gain access to that is typically the case.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a towel prepared for the staying water that will certainly originate from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single taps from transforming during this procedure. When the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing substance.
Before going on to fit the new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the tap and also the other end gives a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will require minimizing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines remain in place in between the faucet and the sink. Protect the faucet in position with the manufacturer supplied backnut. As soon as the faucet is securely in place, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular faucet connectors. The former kind needs to be connected to the tap ends initially, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Setting up the Tub
Making use of both wood boards under its feet, place the bathtub in the needed setting. The wood boards are handy in evenly spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 tiny factors.
The following goal is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the level as well as readjusting the feet on the bath tub till the level reviews degree.
To mount faucets, fit the bottom of the furthest flexible tap adapter to the proper supply pipeline by making a compression sign up with; then do the same for the other tap.
Turn on the water system and also examine all joints and also new pipework for leaks and tighten them if necessary. Load the bath tub as well as additionally examine the overflow outlet and the normal outlet for leaks.
Finally, repair the bath paneling as explained in the producer's instruction manual. Tiling and also sealing around the bathtub needs to wait till the bath tub has actually been utilized at least once as this will certainly resolve it right into its final position.
Preparing for the Setup
First of all, the supporting frame provided with the bathroom ought to be fitted (if required) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is very important to ensure that if the faucet includes a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets unit to stop pressure on the tub.
Fit the flexible tap connectors to the bottom of both taps using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. See to it you utilize every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to currently prepare to be fitted in its last position.
Tiling Around the Tub
In the area where the bath fulfills the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to split a rigid seal, triggering the water to penetrate the wall surface in between the bath and also the tiling, leading to issues with dampness as well as feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your components and installations. They are sold in tubes as well as cartridges, and also are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of drenched newspaper or soft rope. Remember to always load the bath tub with water before sealing, to enable the motion experienced when the bathtub remains in usage. The sealant can break relatively very early if you do not take into account this motion prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily offered on the marketplace. It is suggested to fit the tiles utilizing waterproof or water-proof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our post about Installing A Bathtub. Many thanks for taking time to read through our piece. Are you aware of someone else who is in to How to Install a Bathtub? Feel free to promote it. Thanks for taking the time to read it.
Contact Us Report this page